Daewoo DV-500 Instruction Manual download pdf (Page 15)

Before connecting

• The DV-SP500 is shipped with the main power (POWER)

switch in the on position (_ ON). When the power cord is

plugged in for the first time, the DV-SP500 will automatically

enter the standby state and the STANDBY indicator will

light (same condition after step 2 below).

• Make sure that all the connections on pages 13 and 14 are

complete (the connection to a TV is required).

Connecting the Power/

Turning on the DVD Player

Plug the supplied power cord into

the AC INLET and then into the

power outlet on the wall.

• Do not use a power cord other than the

one supplied with the DV-SP500. The

power cord supplied is designed for use

with the DV-SP500 and should not be

used with any other device.

• Never have the power cord

disconnected from the DV-SP500 while

the other end is plugged into the wall

outlet. Doing so may cause an electric

shock. Always connect by plugging into

the wall outlet last and disconnect by

unplugging from the wall outlet first.

Press POWER to switch on the main

power.

The DVD Player enters standby mode.

The STANDBY indicator lights up.

• The buttons on the remote controller do

not operate if the POWER switch is set

to OFF.

• To switch off the main power, press

POWER again.

Press STANDBY/ON on the DVD

Player or ON on the remote

controller.

The DVD Player turns on and the STANDBY

indicator turns off.

• To put the DVD Player in the standby

mode, press STANDBY/ON on the DVD

Player, or STANDBY on the remote

controller. Be sure to set the volume to

minimum before putting the DVD Player

in the standby mode for the next use to

avoid sudden loud sound reproduction.

• While the STANDBY indicator lights up,

the DVD Player can receive signals from

the remote controller. However, if you

press POWER on the DVD Player to

switch off the main power, the remote

controller cannot be used to turn on the

DVD Player.

• Setting the STANDBY button to standby

does not shut off the power completely.

To the mains

■ Setting the TV System (except for USA and

Canadian models)

The default setting of this player is AUTO, and unless you notice that

the picture is distorted when playing some discs, you should leave it

set to AUTO.

If you experience picture distortion with some discs, set the TV

system to match your country or region’s system. Doing this,

however, may restrict the kinds of disc you can watch. The table

below shows what kinds of disc are compatible with each setting

(AUTO, PAL and NTSC).

1 Switch the player into standby.

2 Hold down ¢ then press STANDBY/ON to switch the TV

system.

The TV system changes as follows:

AUTO = NTSC

NTSC = PAL

PAL = AUTO

The display indicates the new setting.

Note that you have to switch the player into standby before each

change.

About MOD. (Modulation) PAL

• SHRINK

Most models of the newly developed countdown PAL TV system

detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch

vertical amplitude, resulting in a display without vertical

shrinkage.

• If your PAL TV does not have a V-Hold control, you may not be

able to view NTSC disc because the picture may roll. If the TV

has a V-Hold control, adjust it until the picture stops rolling. On

some TVs, the picture may shrink vertically, leaving black bands

at the top and bottom of the screen. This is not a malfunction; it is

caused by the NTSC = PAL conversion.

Type

DVD

Video CD

CD, No disc

Format

NTSC

PAL

NTSC

PAL

Disc Output format

Position of TV SYSTEM mode

NTSC PAL AUTO

NTSC MOD. PAL NTSC

PAL PAL

NTSC MOD. PAL NTSC

NTSC PAL PAL

NTSC PAL NTSC or PAL

INLET

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 59 60

Comments to this Manuals

No comments

Daewoo DV-500 Instruction Manual Page 15

Comments to this Manuals

Related products and manuals for DVD players Daewoo DV-500