Daewoo DWF-806 Service Manual

Service ManualAuto WasherModel : DWF-750/752/800/802753/755/803/805756/758/806/808DAEWOO ELECTRONICS CO., LTD.

95. FEATURE AND TECHNICAL EXPLANATIONEXPLANATIONWASH DRAIN SPIN FILL RINSE 1 DRAIN SPIN FILL RI

10EXPLANATIONFUNCTIONAL PRINCIPLE1 The micom can remember the time from the begining of drain to reset point when the pressure switch reaches to“OFF”

11EXPLANATIONThis is the device to dispense the softener automatically by centrifugal force.This is installed inside the auto-balancer.FUNCTIONAL PRIN

12EXPLANATIONAutomatic Unbalance AdjustmentCirculating-WaterThe alarm finished when you close the lid after opening it. Check the unbalance of the was

13EXPLANATIONMuch lint may be obtained according to the kind ofclothes to be washed and some of the lint may alsosticks to the clothes.To minimize thi

14EXPLANATIONThe proper water currents is made by the rotation of pulsator at a low speed to prevent the damage to the smallsized clothes.STRUCTUREPul

15EXPLANATIONPRINCIPLE OF INTAKE & OUTLET OF THE AIRINTAKE : ARMATURE moves up, and BELLOWS inhales the air. At the same time, protector B is open

16DIRECTIONS6. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT¡ Raise the top plate on the outer cabinet.¡ Remove outer tub cover from the tub ass’y.¡ Remov

17DIRECTIONS¡ Lay the front of the washer on the floor.¡Remove four bolts mounting the plate-gear protect byusing a box wrench and remove plate-gear p

18DIRECTIONS¡ Loosen the adjustment bolt and turn the adjust-ment bolt until the end of the bolt touches to thebrake lever.¡ Tighten the lock nut and

ASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHTO WASHER AUTO WASHER AUTO W

19THE REPAIR7. THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM¡¡TOOL FOR REPLACING THE CLUTCH BOSS ASSEMBLE¡¡Tool name Specification Q’t

20THE REPAIRNO. PARTS NAME SPECIFICATION CODE Q’TY1 CLUTCH SPRING 1.5*1.5 3615110000 12 CLUTCH BOSS PP 3619301300 13 GREASE beacon#325 3gPACKING PACKI

21THE REPAIRNo. Process NoticeDisassemble 11234Release screws marked 4-pointRemove the protectorRemove the v-beltLoosen the fastening nutDisassemble t

22THE REPAIRNo. Process NoticeDisassemble 25678Disassemble the pulleyDisassemble the clutch bossassemblySeparate coupling from clutchboss ass’yCleanin

23THE REPAIRNo. Process NoticeAssemble 11234Assemble the couplingAssemble the new clutch bossass’yAssemble the pulleyAssemble the spring washerCheck t

24THE REPAIRNo. Process NoticeAssemble 25678Clutch TipDrainValveSynchronousMotor3.5~4.5keep distance 2~3mmAssemble the fastening nutAssemble the BeltA

8. TROUBLE SHOOTING GUIDE25TROUBLE SHOOTINGPROBLEMWATER IS NOT SUP-PLIED.CHECK POINTDo you open the watertap?Is the filter of the waterinlet valve clo

26TROUBLE SHOOTINGPROBLEMWATER SUP-PLY IS NOTSTOPPED.CHECK POINTDoes the water supplycontinue while the poweris turned off?Does the water supply start

27TROUBLE SHOOTINGPROBLEMTHE WASHERDOES NOTDRAIN.CHECK POINTDo you install thedrain hose properly?Is the foreign matteraccumulated insidethe pump hous

28TROUBLE SHOOTINGPROBLEMTHE WASHERDOES NOTSPIN.CHECK POINTIs the lid open?Does the safety switchoperate normally?Does the pulsator rotatewhile the tu

1. SPECIFICATIONS2SPECIFICATIONSNO. ITEM1 POWER SOURCE AVAILABLE IN ALL LOCAL AC VOLTAGE2POWER 50Hz 320WCONSUMPTION 60Hz 300W(110~127V) / 340W(220

29TROUBLE SHOOTINGNONOPROBLEMTHE INDICA-TORLAMPS(L.E.D)DO NOT LIGHTUP WHEN THEPOWER BUT-TON ISPRESSED.PROGRESSLAMPS(LED)DO NOT LIGHTUP.MOTORROTATESWHE

9. PRESENTATION OF THE P.C.B ASS’Y30PCB ASS’YMESSAGE CAUSE SOLUT

APPENDIX31WIRING DIAGRAM§§Wiring Diagram [non-pump]

32WIRING DIAGRAM§§[Non-Pump, Single Valve]

33WIRING DIAGRAM§§[Pump]

34WIRING DIAGRAM§§[pump, single valve]

35PARTS DIAGRAM§§Parts Diagram

36PARTS DIAGRAM§§Parts ListNO. PART NAME PART CODE SPECIFICATION REMARKA01 PLATE T 3614521500 PP A02 DOOR B AS 3611797600 ABS OPTION : A03 DOOR

37PARTS DIAGRAMNO. PART NAME PART CODE SPECIFICATION REMARK3612787945 5A COLD/HOT NON-BUBBLE DUAL VALVE, PUMP3612787970 8A COLD/HOT BUBBLE A26 HARNES

38PARTS DIAGRAM

2. STRUCTURE OF THE WASHING MACHINE3STRUCTURE • GROUND WIRE In case of 3-wire power cord, ground wire will not be provided • POWER CORD• DRAIN

39PARTS DIAGRAM§§Parts ListNO. PART NAME PART CODE SPECIFICATION REMARKB01 CABINET 3610809600 PAINTED STEEL SHEET 0.6T B02 HANDLE CABINET 36126033

40PARTS DIAGRAM

41PARTS DIAGRAM§§Parts ListNO. PART NAME PART CODE SPECIFICATION REMARKC01 BALANCER AS 3616104700 DWF-6010 C02 TUB I 3618808500 SUS 0.5T C03 TUB

42PARTS DIAGRAM

43PARTS DIAGRAM§§Parts ListNO. PART NAME PART CODE SPECIFICATION REMARKD01 COVER TUB O 3611414600 PP D02 TUB O 3618817600 PP D03 SUSPENSION AS F

44CIRCUIT DIAGRAM§§Circuit Diagram1. DWF-750/752/803/805/753/755/803/805

452. DWF-756/758/806/808

S/M NO. : WF750SE001DAEWOO ELECTRONICS CO., LTD.686, AHYEON-DONG MAPO-GU SEOUL, KOREAC.P.O. BOX 8003 SEOUL, KOREATELEX: DWELEC K28177-8CABLE: “DAEWOOE

3. FUNCTIONS OF THE CONTROL PANEL4CONTROL PANEL• Press this switch to turn the power on or off.• It can be used to choose water temperature to be supp

5PROCEDURE• Press this switch to turn the power on or off.• It can be used to choose water temperature to be supplied.• As the button is pressed, wate

64. DIRECTIONS FOR INSTALLATION AND USEDIRECTIONSThe opening must not be obstructed by carpeting when the washing machine is installed on a carpeted f

7CONNECTIONFOR ORDINARY TAP6Connect the inlet hose adapterof the hose to the water inlet ofthe washer by turning it clock-wise to be fixed tightly.• P

8CONVENIENCE§§How To Clean The Filter4Remove the dirtfrom the inlet filterwith a brush.1Pull the power plugout beforecleaning it.2Turn off thewater su